1 The Sargent & Greenleaf Rotarybolt Z02 lock combines ease of operation with security and flexibility. Its advanced electronic circuit design makes it easy to open and easy to change codes. Follow these instructiOns carefully to get the best possible use from your The Sargent & Greenleaf Rotarybolt Z02 lock is shipped from the factory in single user mode with a factory master code only. It is 1 2 3 4 5 6 #. This code is used to open the lock and set or change all of its codes. If the safe maker or your dealer sets a new master code, he will advise you of the change. You should set the lock to your own, unique master code immediately.
2 The Rotarybolt Z02 lock in single user mode will always open on the master code. At your discretion, it can also be set to accept a supervisor code, up to five different user codes, and a time delay override code. The master code holder is responsible for maintaining the number of active users programmed into each lock. The supervisor code holder can create, change, and delete user codes. The master code is designated as code #1. The supervisor code (if set) is designated as code #2. The user codes (if set) are designated by user numbers 3, 4, 5, 6, and 7. The time delay override code (if set) is designated as code #9.
3 Each time a button is pressed, the lock acknowledges it by sounding a chirp, and the LED on the keypad will light momentarily as the chirp sounds. All codes must contain six digits or six letters. Any digit or letter can be used as many times as you wish. For instance, the following codes (while not recommended) will operate the lock: 5 5 5 5 5 5 # OR J J J J J J # All codes end with #. This signals the lock that you have finished entering all digits of the code. If you pause more than 10 seconds between button presses when entering a code, the lock will assume you do not want to continue, and it will reset itself to the original code.
4 To open the lock, begin the code entry sequence again from the first step. If you realize you have pressed an incorrect button when entering a code, press * or simply pause ten seconds or more, then begin entering your code again. If four incorrect codes are entered in a row, the Rotarybolt Z02 lock will shut down for a period of five minutes. This is a security feature. Pressing any button anytime during the lockout period will reset the timer to its maximum penalty time. Do not touch any keypad buttons for a period of at least five minutes, then enter any valid code(s) to open the lock.
5 The lock can also go into the lockout period during programming if it interprets an incorrect programming sequence as four or more consecutive incorrect code entries. If the lock emits a long error tone (brap) during repeated programming attempts, it may be in lockout mode. Do not press any buttons for five minutes, then try again. The Rotarybolt Z02 lock is extremely versatile, and therefore somewhat complex to program. These detailed programming instructiOns are followed by a condensed, two-page quick programming reference designed for anyone who is already familiar with the lock s various features.
6 For UL installations, the maximum number of user codes is : This lock has been Listed by Underwriters Laboratories for use with the following S&G keypad(s): 6120-0XX, 6120-2XX, 6120-4XX, 6160-2XX (IP Series), 61KP-1XX Copyright 2004, Sargent & Greenleaf, instructiOnsRotarybolt Z02 Electronic Safe LockDocument 630-649 Revised 12/22/05 Sargent & Greenleaf, Wholly Owned Subsidiary of Stanley Security Solutions, Box 930 Nicholasville, KY 40356 Phone: (800)-826-7652 Fax: (800)-634-4843 Phone: (859)-885-9411 Fax: (859)-887-2057 Sargent & Greenleaf , Chemin du Croset1024 Ecublens, SwitzerlandPhone: +41-21 694 34 00 Fax: +41-21 694 34 09to open the LockPress the code digits or letters in order, followed by #.
7 The lock bolt will retract for six seconds, allowing you time to operate the safe handle and open the door. Do not put any pressure on the safe handle until after the code has been entered. The Rotarybolt Z02 lock will lock automatically when the safe door is closed and the handle is turned to the locked : The Master Code Holder is responsible for maintaining the number of active users programmed into each case of troubLeIf your lock should fail to open when a valid code is entered, check for the following:1. The boltwork of a safe can, under certain conditions, place pressure on the side of the lock s bolt.
8 This is often caused by something inside the safe pressing against the door or by something caught between the safe door and its frame. When this occurs, the lock will not operate properly. To relieve side pressure on the lock bolt, move the safe s handle to the fully locked position, then re-enter a working code. The lock should If the lock chirps when keys are pressed, but it will not open, the batteries may be drained to the point that they will not operate the lock s solenoid. Follow the battery replacement procedure in this If the lock makes no sound when any of the keys are pressed, dead batteries are likely to be the cause.
9 Follow the battery replacement procedure in this This item applies to the two-battery keypad only: If the lock makes no sound when any of the keys are pressed, but the batteries have been checked and found to be good, a loose keypad connector may be the cause. Pull the keypad away from the base as described in the battery changing procedure. Check to make sure the wire connector is firmly seated into its receptacle on the keypad circuit board. The connector is designed so that it will only slide into the receptacle when aligned instructiOnsRotarybolt Z02 Electronic Safe Lock Copyright 2004, Sargent & Greenleaf, all of the preceding remedies have been exhausted and the lock still does not open, contact a qualified safe technician in your area for professional connector being inserted into the receptacle on the keypad circuit 2 Operating instructiOnsRotarybolt Z02 Electronic Safe Lockdec IsIons Mrc and tdoMrc ManageMent reset codeBefore any buttons are pressed, you need to make some decisions.
10 Each Rotarybolt Z02 lock has a factory installed management reset code (MRC), and you need to decide if your lock will keep the management reset code it was shipped with or get a new one of your own choosing. Any MRC change must be programmed into the lock before the master code is changed for the first time. After the master code is changed, the MRC cannot be changed or factory set management reset code is stored in a small, black, plastic envelope packaged with the lock. The maker of your safe may retain the MRC to provide safe storage so that it will be available in the event it must be used.
Show more
